Automotive

Automotive lighting design in TracePro: headlamps, rear lamps and LED indicators

Automotive lighting is not just about brightness. A headlamp must light the road well without dazzling other drivers, a rear lamp must be visible and unambiguous, and interior indicators must be legible by day and by night. Such requirements are checked on a model before any injection mold is made.

Automotive lighting design in TracePro: headlamps, rear lamps and LED indicators
Request a quote Start a trial

Automotive light sources have several characteristics that make design difficult: complex geometry of reflectors and lenses, multiple reflections and very strict requirements for the light distribution. In addition, lighting is a styling element, so the appearance of a lamp matters as much as its function.

TracePro is a program designed for such tasks. It uses non-sequential Monte Carlo ray tracing and lets you build a model of the entire lamp: the light source, reflector, lenses, housing and outer lens. We write about the design process of TIR lenses for LEDs in the article How to design a TIR lens for an LED.

What automotive lighting requires

Different lamps have different requirements.

Headlamps must provide the right light distribution on the road, with a sharp cut-off between the lit and dark areas, so as not to dazzle other road users.

Rear and warning lamps must be visible from a wide range of angles and have a specified intensity and color.

Interior lighting, including ambient lighting, and the instrument panel must be uniform and legible, while not causing reflections in the windshield.

Each of these goals can be expressed numerically, as a distribution of intensity, luminance or candela, and checked on a model.

Model elements in TracePro

In TracePro a 3D model is built from CAD geometry, and optical properties are assigned to surfaces and materials: reflection, transmission, absorption and scattering. The light source can be an LED, an HID lamp or an incandescent lamp, and rays are then traced through the whole lamp assembly.

Lambda Research lists the following among TracePro applications in the automotive industry:

  • headlamps and rear lamps,
  • interior ambient lighting,
  • instrument panel and gauges,
  • HUD displays,
  • warning lamps,
  • door handles, footwells and trunks,
  • glazing systems.

Light guides and TIR

Interior lighting and indicators often use light guide plates or rods, in which light is guided by total internal reflection (TIR). Lambda Research describes light guide design using TIR, including chamfered corners that act as mirrors.

The model lets you check how the light passes through the light guide and where it leaves it. This makes it possible to choose the geometry so that the indicator glows uniformly and light does not escape in unwanted places. We describe early checking of ray paths in the CAD environment in the article Visualizing optical simulation results in RayViz.

Results: candela, luminance, illuminance

The result of a lighting simulation is not a picture of rays, but a distribution of photometric quantities. Lambda Research lists among the results:

  • candela plots, showing the luminous intensity in individual directions,
  • luminance maps, showing what a luminous surface looks like, for example an instrument panel,
  • three-dimensional illuminance maps of surfaces,
  • photorealistic visualizations under conditions close to real ones.

Visualizations matter for styling, because they let you assess the look of the lamp before a prototype is made, while candela plots and illuminance maps are used to check the functional requirements.

Regulations and type approval

Automotive lighting is subject to regulations that specify minimum and maximum intensities in given directions. Lambda Research materials on the Lighting Toolkit mention visualization tools and regulation tables with pass/fail criteria for the ECE, SAE, IESNA and FMVSS standards. The scope of these tools in a specific edition of TracePro should be confirmed before purchase.

Regardless of this, remember that simulation supports the design, while type approval is based on photometric testing of finished lamps.

OSLO and RayViz in lighting design

When the lamp contains imaging or collimating lenses, they can be designed in OSLO and transferred to TracePro, which accepts the LEN file format. Early verification of the solid and ray paths in SOLIDWORKS is possible with RayViz, and the model can be saved in the TracePro format for full analysis.

Example workflow for designing an automotive lamp

1. Define functional and styling requirements

Specify the light distribution, color, visibility and the appearance of the lamp in the lit and unlit state.

2. Build the geometry model

Import the lamp solid from CAD and assign materials and surface properties.

3. Define the source

Choose an LED, HID or incandescent source and its angular distribution.

4. Run ray tracing

Check the initial light distribution and ray paths.

5. Evaluate photometric results

Analyze the candela plot, illuminance maps and luminance maps.

6. Improve the geometry

Modify the reflector, lenses or light guide and repeat the simulation.

7. Check the appearance and stray light

Create a photorealistic visualization and check for unwanted reflections and glare.

8. Correlate with measurement

Compare the model with prototype measurements and correct the parameters.

Which tool for which task

Task Tool
Model of the lamp, reflector and light guide TracePro
Intensity distribution, candela, luminance TracePro
Photorealistic visualization TracePro
Design of lenses in the lamp OSLO
Early verification of ray paths in CAD RayViz

The most common mistakes in automotive lighting design

An ideal source

A real LED has a finite size and an angular distribution that must be included in the model.

Ignoring materials and surfaces

Scattering and reflections on the surfaces of the lamp change the light distribution.

Focusing only on brightness

The light-dark cut-off, uniformity and absence of glare are just as important.

No assessment of appearance

A lamp must also look good when lit, not just meet the photometric requirements.

Treating simulation as type approval

Simulation supports the design, but does not replace photometric testing of the finished lamp.

Summary

Automotive lighting design requires simultaneous control of function and appearance: the light distribution on the road, the visibility of lamps, the uniformity of indicators and the styling. TracePro lets you build a model of the entire lamp, trace light through the reflector, lenses and light guides, and evaluate results as candela, luminance and illuminance, as well as photorealistic visualization.

OSLO and RayViz complement this workflow, helping to design the lenses and verify the geometry early. This way problems are detected before an expensive mold is made.

Manufacturer resources

Automotive lighting in TracePro: Lambda Research: Automotive Lighting Design with TracePro

Headlamp design in TracePro: Lambda Research: Designing Automotive Headlamps from Glare to Perfection with TracePro

Smart vehicle lighting: Lambda Research: Smart Lighting Solutions for Vehicles Using TracePro

Frequently asked questions
Automotive lighting design in TracePro: headlamps, rear lamps and LED indicators

Is TracePro suitable for automotive lighting design?

Yes. According to Lambda Research, TracePro helps engineers analyze and optimize LED, HID and incandescent lighting in vehicles, including headlamps, rear lamps and interior lighting.

Which automotive lighting elements can be modeled?

The manufacturer lists headlamps and rear lamps, interior ambient lighting, dashboards and gauges, HUD displays, warning lamps, door handles, footwells and trunks, and glazing systems.

What are TIR light guides used for?

Light guide plates and rods use total internal reflection (TIR) to guide light within the material. TracePro lets you check how the light is guided, for example at chamfered corners that act as mirrors, and where it leaves the guide.

What results can be obtained from simulation?

According to Lambda Research, these include luminance maps showing the appearance of an instrument panel, candela plots (luminous intensity in given directions), three-dimensional illuminance maps of surfaces, and photorealistic visualizations.

Does TracePro check compliance with type-approval regulations?

Lambda Research materials on the Lighting Toolkit mention regulation tables and pass/fail criteria for standards such as ECE, SAE, IESNA and FMVSS. The availability and scope of these tools in a specific edition of the program should be confirmed with the distributor.

Does simulation replace photometric testing?

No. Simulation lets you design and compare variants, but finished lamps undergo photometric testing and type-approval procedures. Measurement results should be fed back into the model.

Ready to check it on your own project?

Ask our engineers for a tailored quote or start a free trial today.

Request a quote Start a trial

← All articles